Currently browsing: IMPA CODE

Aqua Break RX 20 Ltr

WHY RXSOL-16-3003-020 is better ?

An economical  highly concentrated product.
Compatible with oily water separators.
Releasing the oil phase for reclamation.
Suitable for all types of floors. Deodorizing nature.
Eliminates the need to buy & stock duplicate products because of its effectiveness.
Also used for gas and hydrocarbon freeing of tanks. Free from caustic & hydrcarbon, Non flammable Water based, Biodegradable. Safe to metal
 …..

Read more

Aqua Break RX 25 Ltrs

Method of Application and Doses:- 
1st of all by stripping suction removes all possible oil (greasy materials). To prevents evaporation of lighter fraction oil flush the system with cold water.May be brushed on, sprayed (Hand spray/Direct injection) recirculate  the system with RXSOL-16-3003-025 Solution

1.

Cleaning with   washing machines. Dose rate: 0.3-5 ltr per ton wash water (0.03-0.5%).     

2.

Cleaning with recirculation method. Dose rate: 0.5-10 ltr per ton wash water, (0.05-1…..

Read more

AQUA Tuff High Foam conc.

Cleaning agents used in Aquatuff  for hold cleaning solution is fully biodegradable and not be harmful to the marine.  Allow the Aquatuff High foam solution to act for 10-20 minutes thereafter wash the chemicals with high pressure. Due to compatibility and non hazardous nature of Aquatuff makes it superior all purpose cleaner for tank and cargo hold cleaning to essential maintenance tasks in the engine room, or general cleaning of crew and galley areas, every cleaning task.
Heavy Soil deposit…..

Read more

Hydrocarbon Remover Hcf

Using Procedure:-

First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2008-HCF is by direct injection followed by recirculation washing, using tank cleaning machines.

Spraying Method:- 

Using HCF as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at lea…..

Read more

Bentonite Powder

Bentonite can be Broadely classified in 2 grades :
 
Granular: Granular is the preferred option for filling trenches where the conductor is covered with Bentonite and then water poured over and mixed in the trench.
 
Powder: Powder is the preferred method for pouring into bore holes to en-sure the mixture is of a thin enough consistency to reach the bottom of the bore hole. If diamond drilling is required for deep holes, possible 40m depths and deeper and the Bentonite is to be pumped throug…..

Read more

Resuscitate Acid Cleaner

Cleaning of equipment such as pasteurizers, sterilizers and evaporators by removal of salts, lime and rust spots. Also it renews the appearance of ceramic tile, porcelain tile, grout, granite, slate, and sandstone. It is also biodegradable and emits fewer vapors than typical acid cleaners. …..

Read more

Natural Blue Biodegradable cleaner and Degreaser

Storage and Handling :

Store product in the unopened container in a dry location. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.Material removed from containers may be contaminated during use. Do not return product to the original container. Rx Marine International cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated. If additional information is…..

Read more

Methanol Water Mix

Methanol Reformer Fuel Specification : The First Element Methanol Reformer fuel mixture is 66% Methanol / 33% Distilled Water on a volumetric basis. The mixture is prepared in a blend tank of suitable volume. The selected blend tank must be thoroughly cleaned and free of all contaminants. Ensure the mixture is sufficiently blended to produce a homogeneous mixture. …..

Read more

Truck Wash Brightener

Dilute with water before using. The level of dilution depends on the nature and the temperature of the surface being treated.
Can be applied by brushing or high pressure spray wash.
Always Work from bottom to top both on application and rinse. Allow the solution to work for 10 minutes or less prior to rinsing.
Recommended concentrations are 10:1 dilutions for brush application and 20:1 for pressure washing application.
Do not permit solution to dry on surface, rinse completely and preferably by …..

Read more

TRUCK Mounted Cleaner Descaler

Dilutions rates recommended : 
Light Duty Cleaning      : 500 Gram  : 4 Ltrs WATER
Normal Cleaning           :  1 Kg  : 4 Ltrs WATER  15 minutes  or  Time duration can be increased up to 45 minutes for Heavy deposit cleaning.
Heavy Duty Cleaning    : 1 Kg  : 4 Ltrs WATER   15 minutes…..

Read more

FORE and AFT

For cleaning of hard surfaces, such as decks, tanks, engine-rooms, etc. These two steps are followed:
High Molecular mixture of CATIONIC and ANIONIC surfactant, to react with all oil and grease molecule
 

Step

1:

Spray directly on area to be cleaned

Step

2:

With high-pressure clean entire emulsified area

Due to high emulsification & penetration objects achieves optimal cleaning results.
Due to repulsion activity fore aft-Rx preventing dirt from reformin…..

Read more

Corrosion Inhibitor for Diesel Cooling Water Treat

Initial dosage for an untreated system is 9 litres of RXSOL CIDC / 1000 litres of untreated distilled water. This will bring the treatment up to the minimum level of 1000 ppm nitrite. For best result and prolonged engine life add RXSOL CIDC every 500 -6500 km. or 250 to 300 hours of running time or every 2 month interval……

Read more