Functions Complete removal of dirt, oil, carbonized grease, heavy oil, gum , vegetable oil , Lube oil, soot , asphalt , carbon stains etc. Gives clear finish to the surface. RXSOL-19-1421-025 is a unique formulation blended from inorganic, organic Compound and solvent with powerful dispersing agent .Readily soluble in water in all proportions.RXSOL-10-1005-210 is non- corrosive to metal like copper, aluminium, Mild steel, and plastic.It is non toxic which makes handling easy.
Due to its equal balance of hydrophobic and hydrophilic characteristic , this product is highly suiable for industrial cleaners, rust removers, hard surface cleaners, and also can be used as disinfectants. Popular and very versatile cleaning product.
|APPEARANCE||Clear brown liquid|
|Emulsifying Property||Good for emulsification of Oils , Gum , Wax, Greases , Polymer & Solvents ,|
|Metal||No known effect|
|Synthetic rubber||May swell|
|Wetting Property||Good Wetting & Emulsifying Property|
|PACKAGING||Order No: RXSOL-19-1421-025||
Size (in litres)
25 / 30 / 210
Advantages: RXSOL-19-1421-025 is easily soluble in water Action is quite fast even at low temperature which gives advantages of cleaning under operation And avoid shut down and down time. Non corrosive to most of the metals / plastics. Gives clear finish to the surface.
Lower cost due to high concentration
Fields of Application: Treated for the really tough daily cleaning problems faced in the proper Maintenance of Industrial and Institutional physical plants. Can be used as a stripper for all types of waxes and finishes and as a Degreaser where regular cleaners will not perform. May be brushed on , sprayed or used in a dip tank . Excellent for use as a wash for fuel tankers & as a liquid steam jenny compound.
Caution : Although RXSOL-19-1421-025 is non toxic &non irritant avoid skin or eye.Contact. If contact occurs wash with ample quantity of water
Proedure Of Use :
1st Method : Mix 1 part of RXSOL-19-1421-025 with 2 -10 parts of water / GAS-OIL , For heavy oil,greasy surface use directly)Spray directly on the entire surface to be cleaned. This can be achieved by Hand spray / mechanical spray pump. Immediately after 2 -5 minute of spray the RXSOL-19-1421-025 starts its function. The Dirt, oil grease etc will loosen. 5 to 6 minutes after spraying start rinsing the system with water (High pressure recommended). Dirt and mud starts vanishing with cleaning media and water.
2nd Method: Application in immersion process with or without ultrasonic support, manual wipping.
3rd Method: RXSOL-19-1421-025 is also used in conjunction with alkaline degreasing bath at 3-5% (v/v) concentration for better and quick degreasing action. Eithers the bath is heated to be 70c or the solution can be stirred or air agitated.
Chemical Tank Cleaning
FOR TANK CLEANING
RECOMMENDATION : 0.2% TO 100%
Procedure for Use :-
- RXSOL-19-1421-025 is highly concentrate
- Dilute in water as per surface deposition.
- Diluted materials apply on rusted area for 15 to 20 minutes then wash off with water repeat if necessary. For stubborn rusted stains.)
RXSOL-19-1421-025 should be applied at full concentration for heavy stains, or diluted to 20-50% for light stains. Allow to soak for 15 to 30 minutes and wash off with water. A second application may be necessary to remove the stubborn stains.
Spraying Direction :-
Using an empty / clean 210 liter drum, fill with 190 liter of fresh water and add 20 liters of RXSOL-19-1421-025 This makes a 10% solution, which can be sprayed onto areas. Once spraying is completed, wait 20-30 minutes and fresh water rinse with lots of water, if possible use butterworth machines for a more efficient result. This method can be used in stainless tanks to %u201Cfreshen up%u201D the look of the stainless materials. Make sure to rinse the tank very well, as residual detergent within the RXSOL-19-1421-025 will show up in a Wall Wash.
Injection %u2013 Not suitable.
When hand spraying is inadequate (too much area to cover), prepare a 2% – 5% solution in the tank using fresh water, heat solution to 50o C, then circulate the solution through butterworth machines for 3 x 45 minutes drops minimum. When using fixed machine recirculate for a minimum of 3 cycles. Rinse out the tank using hot seawater 85o C for 2 hours making sure that there is no form remaining in the water at the pumpstack drain cock. After the hot wash, the tank must be rinsed with fresh water and dried.
* Use a strainer at the pumpstack when circulating any solution.
Tank Lining %u2013 Stainless / Epoxy, Phenolic
Note: This article uses material from the http://rxmarine.com/