dvr Membrane ALKA Clean RXSOL ORG -10 ( Powder )

RXSOL ORG 10 is a high pH formultion that has been designed specifically to remove organics, silt and other particulate deposits from all polyamide, polysulfone and thin film composite membrane surfaces.

RXSOL ORG 10 is a powdered buffered alkaline detergent developed , Especially for cleaning alkaline tolerant reverse osmosis and ultrafiltration membranes.

Information:

REVERSE OSMOSIS MEMBRANE Powder CLEANER with ALKALINE nature for effective cleaning of  COLLOIDAL FOULING, BIOFILM AND ORGANIC FOULANTS TYPICALLY FOUND IN REVERSE OSMOSIS AND NANO-FILTRATION MEMBRANES SYSTEMS.
 
 
This product APPEARANCE is WHITE POWDER – PH OF A 2% SOLUTION –  12.0  and BULK DENSITY – 0.95
 

Technical Specifications:

This advanced, high s trength powder has the following features:

  • pH adjusted to 10+ 0.5
  • Highly effective at ambient temperatures
  • Contains no surfactants and is quickly rinsed away
  • Contains detergent builders, chelating agents and pH buffer

RXSOL ORG-10  is suitable for use with all polyamide, polysulfone and thin film, composite membranes. It can be used at temperatures from 15°C (60°F) up to the maximum recommended by the membrane manufacturer.

The standard dilution ratio is 25 grammes of ORG 10 per litre of water.
 

PROPERTIES    

Form %u2026%u2026%u2026%u2026%u2026%u2026……….powder    Alkalinity

Color%u2026%u2026%u2026%u2026%u2026%u2026%u2026%u2026… white Active as  Na2O%u2026%u2026%u2026%u2026%u2026%u2026 16.2%

Foam %u2026%u2026%u2026%u2026…%u2026%u2026%u2026.. High                                 
Total as Na2O %u2026%u2026%u2026%u2026 19.8 %

PH of 1% solution %u2026%u2026. 10 to 12

Remarks:

RXSOL ORG 10 is also suitable for meat and poultry plant as a cleaner for reverse  Osmosis and Ultra filtration membranes. RXSOL ORG 10 must be used in a manner which prevents  direct  or indirect contamination of edible.

Application:

Inspect cleaning tank, hoses and cartridge filter. Install new filter elements.
Fill cleaning tank with RO solution then, Slowly add 25 grammes of ORG 10  for each litre of cleaning tank capacity. Thoroughly mix cleaning solution by using a mixer or by circulating it through the cleaning pump. The solution may be heated to improve cleaning effectiveness.
Do not exceed the membrane manufacturer%u2019s temperature limits.
Circulate the solution through the membrane bank in the feed direction for one hour at the flow rate recommended by the membrane or system manufacturer. If the manufacturer%u2019s recommendations are not available, the following guidelines may be used.

Maintains production capacity

Special formula maintains membrane flux rate 

Chelates and buffered alkalinity effectively remove fouling agents from alkaline 

Tolerant   RO and UF membranes

 

BENEFIT ::: 

Dissolves freely to reduce labor and cleaning time, Easy to add balance formulation eliminates need for adding separate additives or boosters, Rinse quickly and completely to reduce cleaning time

 

ITS ADVANCE FORMULATION Makes Economical use cost and recommended use dilution, Chlorine free formulation helps assure compatibility with membrane to Extent membrane life. 

Note:

In cases of heavy fouling, the first return flow (up to 15% of the cleaning tank volume) should be diverted to drain to prevent redeposition of removed solids.
In multi-pass systems, best results will be achieved if each pass is cleaned separately.
The solution should be discarded if it becomes turbid or discoloured by removed material.
A fresh solution should then be prepared before cleaning additional passes.

Rinse with permeate before returning the system to service.

Using Procedure:

Spiral wound membrane

Membrane diameter
(inches)

Flow rate per tube (parallel flow)
l/min (US gallons/min)

4 23 (6)
6 53 (14)
8 91 (24)
10 114 (38)
12 204 (54)

 Hollow fibre membrane

Membrane diameter
(inches)

Flow rate per element (parallel flow)
l/min (US gallons/min)

4 19 (6)
8 57 (24)
10 76 (38)

TO USE 

For normal CIP cleaning or soak cleaning RO and UF system completely , Pre dissolve in warm water before adding to system. Typically used Concentration is 0.7 to 1.5 % or 9-20 ounces of RXSOL ORG 10 per each 10 Gallon (67-150 grams/10 l) f water. Circulate throughout the system for 20 Minutes at a temperature of 120-160 degree F (49 %u2013 71 degree C)

Note: 

Observe the recommendation of the manufacturer of the membrane for  Maximum temperature.

Note: This article uses material from the http://rxmarine.com/