A powerful penetrating mixed chemical products to remove heavy coal deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems.
It is free from hydrocarbon solvents, non flammable and biodegradable.
Biodegradable / Non-Toxic / Non-Pollutant.
VERY Cost effective.
Recommended to use spray equipment.
The use of hot water will greatly enhance the effectiveness of the cleaning and should be utilized whenever possible.
Safety And Handling :-
RXSOL-22-2201 is completely safe to handle, being non-toxic & non corrosive.As with all chemicals general safety and handling procedures apply. Avoid contact with eyes as irritation may occur. Do not take internally. In case of contact with eyes, flush eyes immediately and cupiously with clean running water for 15- minutes and seek medical attention.
%u2022 Use cold – no heating required.
%u2022 Easily dissolves deposits containing carbon , polymer resin etc.
%u2022 Economical to use.
%u2022 Scraping not required.
%u2022 Non- flammable.
%u2022 Helpful for burner tips, fuel injectors and all components fouled by carbon, resin or varnishes.
%u2022 Cleans oil side of fuel heaters, oil coolers, etc.
%u2022 Can be used for cleaning of : -Fuel Oil Filters – Pistons – Piston rings – Valve cage
Directions for Use and Dose Rates
It may be used concentrated or diluted with water, depending on the degree of contamination, the surface area to be treated, the desired degree of cleaning and the available downtime.Actually, the user is the best one capable to regulate the quantity and concentration to be used for the situation at hand.In any case, when the accumulation is not heavy, a 50% solution with water must be used. Otherwise,RXSOL-22-2201. can be used undiluted especially when deposition is heavy and hard spots persist.
Conventional cleaning methods such as a brush,hard sponge, thick and hard broom and /or a mop can be used on heavy duty and hard stain deposits.Note that for heavy accumulations the cleaning procedure might be necessary to be repeated until the results are satisfactory. Furthermore, is important to keep in mind that 1 litre of RXSOL-22-2201 is sufficient to cover a surface area of 8%u201310 square meters.
NOTE ::: — Let this product soak into the surface for 30-45 minutes. Then using a high-powered spray washer blast the surfaces until the stains and discoloration is gone.
%u2022 Cleaning time will vary depending on the extract nature and thickness of deposit to be removal.
%u2022 Stubborn deposits should be scrubbed to assist the cleaning operation.
Your local Rx CLEANSERS representative will work with you to design the optimum concentration & procedure for your system.
RXSOL-22-2201 should be mixed with fresh water to form a solution of 10-30%, depending on the extent of scaling. After using RXSOL-22-2201 it is essential to thoroughly rinse all metal surfaces at least once with a 0.5% solution of Alkalinity Control in fresh water. This solution should be circulated for 2-4 hours or until an acceptable pH value is obtained. This will neutralize any remaining acidity & passivate steel surfaces.
**Read the Material Safety Data Sheet before using this product.**
Other Valuable Hold Cleaners :::
Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020, Part No.- RXSOL-22-2202-050
Part No.- RXSOL-22-2202-035, Part No.- RXSOL-22-2202-210
Slip Coat RXSOL HOLD BLOCK ::: Polymer EMULSION BASED non reactive coating materials which makes thin film barrier on surface after dry. Due to formation of RXSOL THIN barrier film on surface, the cleaning operation after unloading becomes quicker and easier with optimum results. Part No.- RXSOL-22-2210-210, Part No.- RXSOL-22-2210-025, Part No.- RXSOL-22-2210-050
BARRIER HOLD COAT ::: Highly effective ecofriendly Product blending of natural ingredients which is provide thin temprory film on Hold Surface to protect corrosion. This is making barrier between corrosive cargo like Sulphur, Salt, Petcoak, Cement etc and Hold surface. Part No.- RXSOL-22-2211-210
COAL REMOVER rx hold ::: A powerful penetrating mixed chemical products to remove heavy coal deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems. Part No.- RXSOL-22-2215-210, Part No.- RXSOL-22-2201-025, Part No.- RXSOL-22-2201-050
Hold Wash Concentrate RX ::: RXSOL hold wash is a versatile all purpose marine cleaning solution it can be used as a powerful stand alone cleaner for Petroleum oily stains and residues, vegetable and animal fats, as well as dirt, proteins, soils, coal, ore, coke or in combination. Part No.- RXSOL-22-2204-210, Part No.- RXSOL-22-2204-025, Part No.- RXSOL-22-2204-050
Rock Phosphate Cleaner rx hold ::: A powerful penetrating mixed chemical products to remove heavy Rock Phospate deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems. Part No.- RXSOL-22-2201-210
PCS Hold Clean ::: RXSOL PCS is an innovative, concentrated liquid product specifically engineered to attack, penetrate and remove Coal Carbon, pet coke, lime deposition accumulations from cargo and storage tanks, Also Developed for cargo hold cleaning to remove stains. Part No.- RXSOL-22-2208-210
HBI CARGO Hold Wash Concentrate RX::: RX HBI CARGO Hold Wash Concentrate RX is a versatile all-purpose QUALITY marine cleaning solution. It can be used as a powerful stand-alone cleaner for HBI CARGO . it can be used as a powerful stand alone cleaner for HBI CARGO dust and deposition. Part No.- RXSOL-22-2216-210, Part No.- RXSOL-22-2216-025
Note: This article uses material from the http://rxmarine.com/