single wire high density Barbed wire
Thickness of main wire : 3.05mm+/-0.05mm
Thickness of Barbed wire : 2.03mm+/-0.05mm
Points : 4 Points
Length of points : 15mm+/- 1…..
2 strand 4 points barbs
COATING : ( for rust protection)
Lightly Galvanized : for farming / genral purpose
Heavy Galvanized : for salt weather
Plastic Coated : for extra long life
2.0mm & 2.4mm Galvanized
2.6mm & 3.2mm Plastic Coated
Bright Galvanized & Plastic Coated…..
single wire high density RAZOR wire
Thickness of main wire
Thickness of RAZOR
Sharp BLADE Points
Length of points
Main wire, Galvanized coating weight
140 – 180 grams par m2
RAZOR BLADE, Galvanized coating wt
30 – 50 grams par m2
Main wire, tensile strength
Barbed wire, tensile strangth
30 – 50kgs/m2 density
Distance batween RAZOR( pointes)
Length of ma…..
Future & Benefit
Removes grease, grime, oils, soil, gasket cement, epoxies, glues and inks.
Cleans without water.
Contains biodegradable surfactants.
Won't clog drains.
Contains glycerin and lanolin to keep hands smooth.
Cream formulas may be self dispensed or used with problem-free, push type dispenser.
Leaves hands smooth, not sticky.
Withstands multiple freeze/thaw cycles.
Method of Application and Doses:-
1st of all by stripping suction removes all possible oil (greasy materials). To prevents evaporation of lighter fraction oil flush the system with cold water.May be brushed on, sprayed (Hand spray/Direct injection) recirculate the system with RXSOL-16-3003-025 Solution
Cleaning with washing machines. Dose rate: 0.3-5 ltr per ton wash water (0.03-0.5%).
Cleaning with recirculation method. Dose rate: 0.5-10 ltr per ton wash water, (0.05-1…..
Cleaning agents used in Aquatuff for hold cleaning solution is fully biodegradable and not be harmful to the marine. Allow the Aquatuff High foam solution to act for 10-20 minutes thereafter wash the chemicals with high pressure. Due to compatibility and non hazardous nature of Aquatuff makes it superior all purpose cleaner for tank and cargo hold cleaning to essential maintenance tasks in the engine room, or general cleaning of crew and galley areas, every cleaning task.
Heavy Soil deposit…..
Bentonite can be Broadely classified in 2 grades :
Granular: Granular is the preferred option for filling trenches where the conductor is covered with Bentonite and then water poured over and mixed in the trench.
Powder: Powder is the preferred method for pouring into bore holes to en-sure the mixture is of a thin enough consistency to reach the bottom of the bore hole. If diamond drilling is required for deep holes, possible 40m depths and deeper and the Bentonite is to be pumped throug…..
Cleaning of equipment such as pasteurizers, sterilizers and evaporators by removal of salts, lime and rust spots. Also it renews the appearance of ceramic tile, porcelain tile, grout, granite, slate, and sandstone. It is also biodegradable and emits fewer vapors than typical acid cleaners. …..
Methanol Reformer Fuel Specification : The First Element Methanol Reformer fuel mixture is 66% Methanol / 33% Distilled Water on a volumetric basis. The mixture is prepared in a blend tank of suitable volume. The selected blend tank must be thoroughly cleaned and free of all contaminants. Ensure the mixture is sufficiently blended to produce a homogeneous mixture. …..
Dilute with water before using. The level of dilution depends on the nature and the temperature of the surface being treated.
Can be applied by brushing or high pressure spray wash.
Always Work from bottom to top both on application and rinse. Allow the solution to work for 10 minutes or less prior to rinsing.
Recommended concentrations are 10:1 dilutions for brush application and 20:1 for pressure washing application.
Do not permit solution to dry on surface, rinse completely and preferably by …..
Dilutions rates recommended :
Light Duty Cleaning : 500 Gram : 4 Ltrs WATER
Normal Cleaning : 1 Kg : 4 Ltrs WATER 15 minutes or Time duration can be increased up to 45 minutes for Heavy deposit cleaning.
Heavy Duty Cleaning : 1 Kg : 4 Ltrs WATER 15 minutes…..
For cleaning of hard surfaces, such as decks, tanks, engine-rooms, etc. These two steps are followed:
High Molecular mixture of CATIONIC and ANIONIC surfactant, to react with all oil and grease molecule
Spray directly on area to be cleaned
With high-pressure clean entire emulsified area
Due to high emulsification & penetration objects achieves optimal cleaning results.
Due to repulsion activity fore aft-Rx preventing dirt from reformin…..
It must be applied concentrated . May be applied to the surface by brush or spray, agitate stubborn deposits if required with a brush and wipe away residues with clean cloth.
RXSOL-16-1009-020 can also be use in dip tank applications.
Heavily soiled components may require agitation with a brush.
RXSOL-16-1009-020 preferably use in open or sufficiently ventilated areas. RXSOL-16-1009-020should always be used concentrate (without mixing with other solvent.)
For best results apply with eit…..