Aqua Break RX 20 Ltrmore_vert

Read More arrow_forward

bookmark Aqua Break RX 20 Ltrclose

WHY RXSOL-16-3003-020 is better ?

An economical  highly concentrated product.
Compatible with oily water separators.
Releasing the oil phase for reclamation.
Suitable for all types of floors. Deodorizing nature.
Eliminates the need to buy & stock duplicate products because of its effectiveness.
Also used for gas and hydrocarbon freeing of tanks. Free from caustic & hydrcarbon, Non flammable Water based, Biodegradable. Safe to metal
 …..

Aqua Break RX 25 Ltrsmore_vert

Read More arrow_forward

bookmark Aqua Break RX 25 Ltrsclose

Method of Application and Doses:- 
1st of all by stripping suction removes all possible oil (greasy materials). To prevents evaporation of lighter fraction oil flush the system with cold water.May be brushed on, sprayed (Hand spray/Direct injection) recirculate  the system with RXSOL-16-3003-025 Solution

1.

Cleaning with   washing machines. Dose rate: 0.3-5 ltr per ton wash water (0.03-0.5%).     

2.

Cleaning with recirculation method. Dose rate: 0.5-10 ltr per ton wash water, (0.05-1…..

AQUA Tuff High Foam conc.more_vert

Read More arrow_forward

bookmark AQUA Tuff High Foam conc.close

Cleaning agents used in Aquatuff  for hold cleaning solution is fully biodegradable and not be harmful to the marine.  Allow the Aquatuff High foam solution to act for 10-20 minutes thereafter wash the chemicals with high pressure. Due to compatibility and non hazardous nature of Aquatuff makes it superior all purpose cleaner for tank and cargo hold cleaning to essential maintenance tasks in the engine room, or general cleaning of crew and galley areas, every cleaning task.
Heavy Soil deposit…..

Hydrocarbon Remover Hcfmore_vert

Read More arrow_forward

bookmark Hydrocarbon Remover Hcfclose

Using Procedure:-

First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2008-HCF is by direct injection followed by recirculation washing, using tank cleaning machines.

Spraying Method:- 

Using HCF as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at lea…..

Bentonite Powdermore_vert

Read More arrow_forward

bookmark Bentonite Powderclose

Bentonite can be Broadely classified in 2 grades :
 
Granular: Granular is the preferred option for filling trenches where the conductor is covered with Bentonite and then water poured over and mixed in the trench.
 
Powder: Powder is the preferred method for pouring into bore holes to en-sure the mixture is of a thin enough consistency to reach the bottom of the bore hole. If diamond drilling is required for deep holes, possible 40m depths and deeper and the Bentonite is to be pumped throug…..

Natural Blue Biodegradable cleaner and Degreasermore_vert

Read More arrow_forward

bookmark Natural Blue Biodegradable cleaner and Degreaserclose

Storage and Handling :

Store product in the unopened container in a dry location. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.Material removed from containers may be contaminated during use. Do not return product to the original container. Rx Marine International cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated. If additional information is…..

Methanol Water Mixmore_vert

Read More arrow_forward

bookmark Methanol Water Mixclose

Methanol Reformer Fuel Specification : The First Element Methanol Reformer fuel mixture is 66% Methanol / 33% Distilled Water on a volumetric basis. The mixture is prepared in a blend tank of suitable volume. The selected blend tank must be thoroughly cleaned and free of all contaminants. Ensure the mixture is sufficiently blended to produce a homogeneous mixture. …..

Truck Wash Brightenermore_vert

Read More arrow_forward

bookmark Truck Wash Brightenerclose

Dilute with water before using. The level of dilution depends on the nature and the temperature of the surface being treated.
Can be applied by brushing or high pressure spray wash.
Always Work from bottom to top both on application and rinse. Allow the solution to work for 10 minutes or less prior to rinsing.
Recommended concentrations are 10:1 dilutions for brush application and 20:1 for pressure washing application.
Do not permit solution to dry on surface, rinse completely and preferably by …..

FORE and AFTmore_vert

Read More arrow_forward

bookmark FORE and AFTclose

For cleaning of hard surfaces, such as decks, tanks, engine-rooms, etc. These two steps are followed:
High Molecular mixture of CATIONIC and ANIONIC surfactant, to react with all oil and grease molecule
 

Step

1:

Spray directly on area to be cleaned

Step

2:

With high-pressure clean entire emulsified area

Due to high emulsification & penetration objects achieves optimal cleaning results.
Due to repulsion activity fore aft-Rx preventing dirt from reformin…..